Provide NACE NACE-CIP2-001 Practice Test Engine for Preparation
Detailed New NACE-CIP2-001 Exam Questions for Concept Clearance
NACE-CIP2-001 certification exam is designed for individuals seeking to become a certified coating inspector level 2. The National Association of Corrosion Engineers (NACE) is a globally recognized organization that provides technical training and certification programs in the field of corrosion control. The NACE-CIP2-001 exam is one of the most important certifications for professionals in the coating industry.
Achieving the NACE-CIP2-001 certification demonstrates a high level of expertise in the coatings industry and can lead to greater opportunities for career advancement. Certified coating inspectors are often sought after by companies in a variety of industries, including oil and gas, construction, and manufacturing. They may also be eligible for higher salaries and increased job security.
NEW QUESTION # 12
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. run through the air wash separator.
- B. mixed with uncontaminated abrasive
- C. washed with clean potable water prior to Use.
- D. disposed of properly.
Answer: D
NEW QUESTION # 13
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. Explosion resistance
- C. Preferential fuel for the fire
- D. fire extinguishing characteristics
Answer: A
NEW QUESTION # 14
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by SP 3
- C. SP 1 followed by SP 2
- D. SP 1 followed by acid etching
Answer: C
NEW QUESTION # 15
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Flow stage
- B. Cure stage
- C. Wetting stage
- D. Gel stage
Answer: A
NEW QUESTION # 16
NACE International Standards are developed by:
- A. Standard committees
- B. Government mandates
- C. International mandates
- D. Regional mandates
Answer: A
NEW QUESTION # 17
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise the other inspector he is using an incorrect method
- B. Review the specification with the other inspector to see what method was specified
- C. Advise your QC Manager to change the ITP to the use of the salt smart meter
- D. Redo the pre-cleaning based on the other inspectors results
Answer: B
NEW QUESTION # 18
In which type of concrete are laitance commonly encountered?
- A. Glass fiber cement
- B. Gunite
- C. Poured (wet cast)
- D. Concrete block (poured with a form)
Answer: C
NEW QUESTION # 19
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Verbally challenge the NCR
- B. Consult your supervisor
- C. Review the NCR with the other Inspector
- D. Request a re-blast of the item in question
Answer: B
NEW QUESTION # 20
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Heat-shrink sleeves
- B. Coal Tar Enamel
- C. Concrete
- D. Liquid epoxies
Answer: D
NEW QUESTION # 21
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Mainline coating
- D. Areas exposed to Ultra Violet light
Answer: B
NEW QUESTION # 22
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION # 23
External coatings applied to buried pipelines are generally tested for:
- A. Chalking resistance
- B. Cathodic disbondment
- C. Solvent resistance
- D. Gloss level
Answer: B
NEW QUESTION # 24
When observing fabrication defects the NACE Inspector should:
- A. Write an NCR and call the fabricator
- B. Require they be corrected prior to coating
- C. Stop the job immediately
- D. Consult the specification to determine how they should be treated
Answer: D
NEW QUESTION # 25
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that the most would understand
- B. Language that another NACE Inspector would understand
- C. Language that only in the project would understand
- D. Language that only technical experts would understand
Answer: A
NEW QUESTION # 26
A single component water borne acrylic coating cures by:
- A. Solvent Evaporation
- B. Coalescence
- C. Oxidation
- D. Co-Reaction
Answer: B
NEW QUESTION # 27
You can use magnifiers to examine all of the following EXCEPT
- A. Mill scale
- B. Blisters
- C. Surface profile
- D. Surface cleanliness
Answer: D
NEW QUESTION # 28
Examples of non-ferrous metals include
Select All that Apply:
- A. iron
- B. aluminum
- C. copper
- D. mild steel.
Answer: B,C
NEW QUESTION # 29
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Advise the Owner and write a Non-Conformance report
- B. Ignore the situation
- C. Stop the job
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION # 30
An Inspection and Test Plan is required when:
- A. When the Coating Applicator requests one
- B. When the Owner specifies one
- C. When the Inspector requests one
- D. It is always required
Answer: D
NEW QUESTION # 31
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Advise the prospective employer that you cannot accept the position
- B. Accept assignment without hesitation
- C. Review the NACE Attestation prior to making a decision
- D. Meet with the prospective employer to scope of your role
Answer: C
NEW QUESTION # 32
Antifouling coatings are regulated by international treaties.
- A. True
- B. False
Answer: A
NEW QUESTION # 33
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 50 double rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 25 single rubs with a saturated cloth.
- D. 25 double rubs with a saturated cloth.
Answer: A
NEW QUESTION # 34
Pre-cleaning of work pieces will NOT remove
- A. mill scale.
- B. snow, ice or water.
- C. dirt.
- D. oil or grease.
Answer: A
NEW QUESTION # 35
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Inorganic Coatings
- B. Latex
- C. Organic coatings
- D. Polyurea
Answer: A
NEW QUESTION # 36
......
NACE-CIP2-001 2024 Training With 100 QA's: https://www.realexamfree.com/NACE-CIP2-001-real-exam-dumps.html
NACE-CIP2-001 Exam Preparation Material with New NACE-CIP2-001 Dumps Questions.: https://drive.google.com/open?id=1ngRMrnb0D7KWJPnymI1EfEtq0lQPhY1f
