Get Prepared for Your 300-410 Exam With Actual 563 Questions
Valid 300-410 Test Answers Full-length Practice Certification Exams
NEW QUESTION # 181
Refer to the exhibit.
Refer to the exhibit. The IT router has been configured with the Science VRF and the interfaces have been assigned to the VRF. Which set of configurations advertises Science-1 and Science-2 routes using EIGRPAS 111?
- A. Option C
- B. Option A
- C. Option D
- D. Option B
Answer: C
NEW QUESTION # 182
An engineer is troubleshooting on the console session of a router and turns on multiple debug commands. The console screen is filled with scrolling debug messages that none of the commands can be verified if entered correctly or display any output. Which action allows the engineer to see entered console commands while still continuing the analysis of the debug messages?
- A. Configure the logging synchronous command
- B. Configure the no logging console debugging command globally
- C. Configure the term no mon command globally
- D. Configure the logging synchronous level all command
Answer: A
Explanation:
Explanation
Let's see how the "logging synchronous" command affect the typing command:
Without this command, a message may pop up and you may not know what you typed if that message is too long. When trying to erase (backspace) your command, you realize you are erasing the message instead.
With this command enabled, when a message pops up you will be put to a new line with your typing command which is very
NEW QUESTION # 183
Refer to the exhibit.
An engineer must configure PBR on R1 to reach to 10.2.2.0/24 via R3 AS64513 as the primary path and a backup route through default route via R2 AS64513. All BGP routes are in the routing table of R1. but a static default route overrides BGP routes. Which PBR configuration achieves the objective?
- A. Option C
- B. Option A
- C. Option B
- D. Option D
Answer: C
NEW QUESTION # 184 
Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?
- A. Remove the prefix keyword from the distribute-list command.
- B. Change the direction of the distribute-list command from out to in.
- C. Remove the line with the sequence number 10 from the prefix list.
- D. Remove the line with the sequence number 5 from the prefix list.
Answer: D
NEW QUESTION # 185
Refer to the exhibit. A network engineer receives a report that Spoke 1 users can perform bank transactions with the server located at the Center site, but Spoke 2 users cannot. Which action resolves the issue?
- A. Configure OSPFv2 on the routers B and C interfaces
- B. Configure IPv6 on the routers B and C interfaces
- C. Configure the Spoke 2 users IP on the router B OSPF domain
- D. Configure encapsulation dot1q 78 on the router C interface.
Answer: B
NEW QUESTION # 186
Refer to the exhibit.
A client is concerned that passwords are visible when running this show archive log config all.
Which router configuration is needed to resolve this issue?
- A. MASS-RTR(config-archive-log-cfg)#hidekeys
- B. MASS-RTR(config-archive-log-cfg)#password encryption aes
- C. MASS-RTR(config)#aaa authentication arap
- D. MASS-RTR(config)#service password-encryption
Answer: A
Explanation:
NEW QUESTION # 187
Refer to the exhibit.
An engineer has configured R1 as EIGRP stub router. After the configuration, router R3 failed to reach to R2 loopback address.
Which action advertises R2 loopback back into the R3 routing table?
- A. Use a leak map on R1 that matches the required prefix and apply it with the distribute list command toward R3.
- B. Add a static null route for R2 loopback address in R1 and redistribute it to advertise to R3.
- C. Add a static route for R2 loopback address in R1 and redistribute it to advertise to R3.
- D. Use a leak map on R3 that matches the required prefix and apply it with the EIGRP stub feature.
Answer: A
Explanation:
The EIGRP stub feature is useful to prevent unnecessary EIGRP queries and to filter some routes that you advertise. What if you want to configure your router as a stub router but still make an exception to some routes that it advertises? That is possible with the leak-map feature. This is how to configure leak-map in this question:
R1
(config)#ip access-list standard R2_L0
R1(config-std-nacl)#permit host 2.2.2.2
R1(config)#route-map R2_L0_LEAK
R2(config-route-map)#match ip address R2_L0
R1(config)#router eigrp 1
R1(config-router)#eigrp stub leak-map R2_L0_LEAK
NEW QUESTION # 188
Which command displays the IP routing table information that is associated with VRF-Lite?
- A. show run vrf
- B. show ip vrf
- C. show ip protocols vrf
- D. show ip route vrf
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/50sg/configuration/guide/Wrapper-46SG/vrf.html#wp1045708
NEW QUESTION # 189
Drag and drop the IPv6 first hop security device roles from the left onto the corresponding descriptions on the right.
Answer:
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/security/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_Security_Configuration_Guide_7x/b_Cisco_Nexus_9000_Series_NX-OS_Security_Configuration_Guide_7x_chapter_011011.pdf
NEW QUESTION # 190
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 191
Refer to the exhibit.
Which interface configuration must be configured on the HUB router to enable MVPN with mGRE mode?
- A. Option A
- B. Option C
- C. Option D
- D. Option B
Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/15-mt/sec-conn-dmvpn-15-mt-book/sec-conn-dmvpn-dmvpn.html
NEW QUESTION # 192
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Answer:
Explanation:
Explanation
Graphical user interface, application Description automatically generated
NEW QUESTION # 193
What is LDP label binding?
- A. destination prefix with label
- B. neighboring router with label
- C. two routers with label distribution session
- D. source prefix with label
Answer: A
Explanation:
Explanation
Text Description automatically generated with medium confidence
NEW QUESTION # 194 
Refer to the exhibit. R2 has two paths to reach 192.168.13.0/24. but traffic is sent only through R3. Which action allows traffic to use both paths?
- A. Configure the variance 2 command under the EIGRP process on R2
- B. Configure the variance 4 command under the EIGRP process on R2.
- C. Configure the bandwidth 2000 command under interface FastEthernet0/0 on R2.
- D. Configure the delay 1 command under interface FastEthernet0/0 on R2.
Answer: B
Explanation:
Explanation
From the output of the "show ip eigrp topology ..." command, we notice network 192.168.13.0/24 was learned via two routes:+ From 192.168.23.3 (R3) with FD = 1075200 and AD = 281600+ From 192.168.12.1 (R1) with FD = 2611200 and AD = 281600 From the output of the "show ip route ..." command, we learned that the best (and chosen) path is via
192.168.23.3 (R3).
To use both paths (called unequal cost load balancing) with EIGRP, the second path via R1 must satisfy the feasibility condition. The feasibility condition states that, theAdvertised Distance (AD) of a route must be lower than the feasible distance of the current successor route.
In this case, the second path satisfies the feasible condition as its AD (281600) is smaller than the FD (1075200) of the best path. Therefore we can configure loadbalancing with "variance" command.
In other words, EIGRP will install all paths with metric < variance * best_metric into the local routing table, provided that it meets the feasibility condition to preventrouting loop. Therefore we can calculate the variance
> metric / best_metric = 2611200 / 1075200 =2.4.
So with a variance greater than 2 (and must be an integer), we can load balance traffic to network
192.168.13.0/24.
NEW QUESTION # 195
When provisioning a device in Cisco DNA Center, the engineer sees the error message "Cannot select the device. Not compatible with template".
What is the reason for the error?
- A. The template has an incorrect configuration.
- B. The software version of the template is different from the software version of the device.
- C. The changes to the template were not committed.
- D. The tag that was used to filter the templates does not match the device tag.
Answer: D
Explanation:
Explanation
If you use tags to filter the templates, you must apply the same tags to the device to which you want to apply the templates. Otherwise, you get the following error during provisioning: Cannot select the device. Not compatible with template.
NEW QUESTION # 196
Refer to the exhibit.
Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers?
- A. Option C
- B. Option A
- C. Option D
- D. Option B
Answer: C
NEW QUESTION # 197
Refer to the exhibit.
The administrator successfully logs into R1 but cannot access privileged mode commands. What should be configured to resolve the issue?
- A. matching password on vty lines as cisco123!
- B. aaa authorization reverse-access
- C. enable secret or enable password commands to enter into privileged mode
- D. secret cisco123! at the end of the username command instead of password cisco123!
Answer: C
NEW QUESTION # 198 
Refer to the exhibit. Which statement about R1 is true?
- A. OSPF redistributes RIP routes only if they have a tag of one.
- B. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
- C. RIP routes are redistributed to OSPF without any changes.
- D. RIP learned routes are distributed to OSPF with a tag value of one.
Answer: D
Explanation:
Section: Layer 3 Technologies
NEW QUESTION # 199
......
Accurate & Verified 2024 New 300-410 Answers As Experienced in the Actual Test!: https://www.realexamfree.com/300-410-real-exam-dumps.html
300-410 Certification Sample Questions certification Exam: https://drive.google.com/open?id=1li3A6h-3MEEM250aee4lYA_Jg5bvOTfC
