[Feb 17, 2026] Fortinet NSE4_FGT_AD-7.6 Exam Dumps Are Essential To Get Good Marks
Latest Fortinet NSE4_FGT_AD-7.6 Dumps with Test Engine and PDF (New Questions)
NEW QUESTION # 56
Refer to the exhibit. Which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules?
- A. Traffic is distributed based on the number of sessions through each interface.
- B. All traffic from a source IP to a destination IP is sent to the same interface.
- C. All traffic from a source IP is sent to the same interface
- D. Traffic is sent to the link with the lowest latency.
Answer: B
Explanation:
For traffic that does not match any of the defined SD-WAN rules, the default implicit SD-WAN rule is applied. By default, the FortiGate uses a "source-destination IP-based" algorithm, which means all traffic from a specific source IP to a specific destination IP is sent through the same interface.
This ensures that a consistent path is used for traffic between the same source and destination IP addresses.
NEW QUESTION # 57
An administrator suspects that the Collector Agent is not forwarding login events to FortiGate.
What is the most effective troubleshooting step?
- A. Check if TCP port 8000 is open between the collector agent and FortiGate.
- B. Restart the domain controller to refresh authentication services.
- C. Verify if DC agent is enabled on the FortiGate.
- D. Verify if FortiGate is set to use LDAP authentication instead of FSSO.
Answer: A
Explanation:
The Collector Agent communicates with FortiGate over TCP port 8000. Ensuring this port is open and reachable is essential for forwarding login events.
NEW QUESTION # 58
An administrator needs to analyze and resolve port conflicts between SSL VPN and HTTPS administrative access on the same interface.
In which two ways can this be done? (Choose two.)
- A. Keep port 443 for both SSL VPN and HTTPS administrative access on the same interface without any problems.
- B. Change the port number for either the SSL VPN service or the HTTPS administrative service if both are on the same interface.
- C. Disable SSL VPN if HTTPS administrative access is using port 443 on any interface.
- D. Run SSL VPN on one interface using port 443 and enable HTTPS administrative access on a different interface, also using port 443.
Answer: B,D
Explanation:
You can keep port 443 for SSL VPN on one interface and also use port 443 for HTTPS admin access on a different interface. Since the services are bound to different interfaces, no conflict occurs.
If both SSL VPN and HTTPS admin access are required on the same interface, you must change the port number for one of the services to avoid a port conflict.
NEW QUESTION # 59
An administrator notices that some users are unable to establish SSL VPN connections, while others can connect without any issues.
What should the administrator check first?
- A. Ensure that the affected users are using the correct port number.
- B. Ensure that forced tunneling is enabled to reroute all traffic through the SSL VPN
- C. Ensure that the HTTPS service is enabled on SSL VPN tunnel interface
- D. Ensure that user traffic is hitting the firewall policy.
Answer: D
Explanation:
If user traffic is not matching the appropriate firewall policy that permits SSL VPN, users will be unable to establish connections, making this the first aspect to verify.
NEW QUESTION # 60
Refer to the exhibit. Review the intrusion prevention system (IPS) profile signature settings shown in the exhibit.
What can you conclude about the signature when adding the FTP.Login.Failed signature to the IPS Sensor profile?
- A. FortiGate stores a local copy of the packet that matches the signature.
- B. The signature setting includes a group of other signatures.
- C. FortiGate allows this low severity signature packet and creates a log.
- D. The signature setting uses a custom rating threshold
Answer: C
Explanation:
The IPS signature FTP.Login.Failed is configured with the action Pass and Packet logging = Enable. This means FortiGate will allow traffic that matches this signature but will also log the event, since the severity is low and blocking is not applied.
NEW QUESTION # 61
A new administrator is configuring FSSO authentication on FortiGate using DC Agent Mode.
Which step is NOT part of the expected process?
- A. The DC agent sends login event data directly to FortiGate.
- B. FortiGate determines user identity based on the IP address in the FSSO list.
- C. The collector agent forwards login event data to FortiGate.
- D. The user logs into the windows domain.
Answer: C
Explanation:
In DC Agent Mode, the DC agent sends login event data directly to FortiGate without involving a collector agent.
NEW QUESTION # 62
Which three statements about SD-WAN performance SLAs are true? (Choose three.)
- A. They are applied in a SD-WAN rule lowest cost strategy.
- B. They monitor the state of the FortiGate device.
- C. They rely on session loss and jitter.
- D. All the SLAtargets can be configured.
- E. They can be measured actively or passively.
Answer: C,D,E
Explanation:
SD-WAN SLAs monitor metrics like packet loss and jitter to evaluate link performance. SLA measurements can be performed using active probing or passive monitoring. Administrators can configure all SLA target parameters to define performance criteria.
NEW QUESTION # 63
A network administrator has configured an SSL/SSH inspection profile defined for full SSL inspection and set with a private CA certificate. The firewall policy that allows the traffic uses this profile for SSL inspection and performs web filtering. When visiting any HTTPS websites, the browser reports certificate warning errors.
What is the reason for the certificate warning errors?
- A. The SSL cipher compliance option is not enabled on the SSL inspection profile. This setting is required when the SSL inspection profile is defined with a private CA certificate.
- B. The browser does not recognize the certificate in use as signed by a trusted CA.
- C. The certificate used by FortiGate for SSL inspection does not contain the required certificate extensions.
- D. With full SSL inspection it is not possible to avoid certificate warning errors at the browser level.
Answer: B
Explanation:
The certificate warning errors occur because the SSL inspection profile is configured to use a private CA certificate that is not recognized by the browser as being signed by a trusted CA. For the browser to trust the FortiGate's re-signed certificates, the CA certificate used by FortiGate for SSL inspection must be installed in the browser's trusted certificate store. Until the browser recognizes the certificate authority (CA) as trusted, it will continue to display warning errors when accessing HTTPS websites.
NEW QUESTION # 64
Refer to the exhibit. Which two statements are true about the routing entries in this database table? (Choose two.)
- A. All of the entries in the routing database table are installed in the FortiGate routing table.
- B. The default route on port2 is marked as the standby route.
- C. Both default routes have different administrative distances.
- D. The port2 interface is marked as inactive.
Answer: B,C
Explanation:
The routing table in the exhibit shows two default routes (0.0.0.0/0) with different administrative distances:
The default route through port2 has an administrative distance of 20. The default route through port1 has an administrative distance of 10. Administrative distance determines the priority of the route; a lower value is preferred. Here, the route through port1 with an administrative distance of
10 is the preferred route. The route through port2 with an administrative distance of 20 acts as a standby or backup route. If the primary route (port1) fails or is unavailable, traffic will then be routed through port2. Regarding the statement that the port2 interface is marked as inactive, there is no indication in the routing table that port2 is inactive. Similarly, all the routes displayed are not necessarily installed in the FortiGate routing table, as the table could include both active and backup routes.
NEW QUESTION # 65
Refer to the exhibits. An administrator creates a new address object on the root FortiGate (HQ- NGFW-1) in the Security Fabric. After synchronization, this object is not available on the downstream FortiGate (HQ-ISFW).
What must the administrator do to synchronize the address object?
- A. Change the csfsetting on both devices to set downstream-access enable.
- B. Change the csfsetting on HQ-ISFW (downstream) to set configuration-sync local.
- C. Change the csfsetting on HQ-NGFW-1 (root) to set fabric-object-unification default.
- D. Change the csfsetting on HQ-ISFW (downstream) to set saml-configuration-sync default.
Answer: C
Explanation:
On HQ-NGFW-1 (the root FortiGate), the setting set fabric-object-unification local prevents address objects created on the root from synchronizing downstream. To propagate objects across the Security Fabric, this must be set to default. Changing the root's csf configuration to set fabric-object-unification default ensures that new address objects are synchronized to HQ-ISFW and other downstream devices.
NEW QUESTION # 66
You have created a web filter profile named restrict_media-profile with a daily category usage quota. When you are adding the profile to the firewall policy, the restrict_media-profile is not listed in the available web profile drop down.
What could be the reason?
- A. The naming convention used in the web filter profile is restricting it in the firewall policy.
- B. The inspection mode in the firewall policy is not matching with web filter profile feature set.
- C. The web filter profile is already referenced in another firewall policy.
- D. The firewall policy is in no-inspection mode instead of deep-inspection.
Answer: B
Explanation:
Web filter profiles with category usage quotas require the firewall policy to be in proxy-based (deep) inspection mode; if the inspection mode does not match this requirement, the profile will not appear in the drop-down list.
NEW QUESTION # 67
Refer to the exhibit showing a debug flow output.
Which two conclusions can you make from the debug flow output? (Choose two.)
- A. The debug flow is for UDP traffic.
- B. The RPF check fails.
- C. The default gateway is configured on port2.
- D. The matching firewall policy denies the traffic.
Answer: C,D
Explanation:
The default gateway is configured on port2 → The debug output shows find a route:
flag=00000000 gw-0.0.0.0 via port2, which indicates that the default route (0.0.0.0/0) points out port2.
The matching firewall policy denies the traffic → The log line Denied by forward policy check (policy 2) confirms that policy 2 matched and explicitly dropped the traffic.
NEW QUESTION # 68
Refer to the exhibits. The exhibits show the system performance output and default configuration of high memory usage thresholds on a FortiGate device.
Based on the system performance output, what are the two possible outcomes? (Choose two.)
- A. Administrators can access FortiGate only through the console port.
- B. FortiGate drops new sessions.
- C. Administrators can change the configuration.
- D. FortiGate has entered conserve mode.
Answer: B,C
Explanation:
Since memory usage is at 90%, exceeding the red threshold (88%), FortiGate enters a state where configuration changes are still allowed.
In this state, FortiGate drops new sessions to preserve resources and maintain stability.
NEW QUESTION # 69
Refer to the exhibit. The NOC team connects to the FortiGate GUI with the NOC_Access admin profile. They request that their GUI sessions do not disconnect too early during inactivity. What must the administrator configure to answer this specific request from the NOC team?
- A. Move NOC_Access to the top of the list to ensure all profile settings take effect.
- B. Increase the offline value of the Override Idle Timeout parameter in the NOC_Access admin profile.
- C. Ensure that all NOC_Access users are assigned the super_admin role to guarantee access
- D. Increase the admintimeout value under config system accprofile NOC_Access.
Answer: D
Explanation:
The admintimeout setting in the admin access profile controls the inactivity timeout for GUI sessions. Increasing this value will extend the session duration before automatic disconnection.
NEW QUESTION # 70
You have configured the FortiGate device for FSSO. A user is successful in log-in to windows, but their access to the internet is denied.
What should the administrator check first?
- A. Whether the user is assigned to the correct AD group.
- B. The FortiGate FSSO active users list for user's IP address.
- C. The windows event viewer for failed login attempts.
- D. The FortiGate firewall policy settings for SSL decryption.
Answer: B
Explanation:
Checking the active users list verifies if FortiGate correctly associates the user with their IP address, ensuring proper policy enforcement for internet access.
NEW QUESTION # 71
You have configured an application control profile, set peer-to-peer traffic to Block under the Categories tab, and applied it to the firewall policy. However, your peer-to-peer traffic on known ports is passing through the FortiGate without being blocked. What FortiGate settings should you check to resolve this issue?
- A. Replacement Messages for UDP-based Applications
- B. Network Protocol Enforcement
- C. Application and Filter Overrides
- D. FortiGuard category ratings
Answer: B
Explanation:
Network Protocol Enforcement settings control how FortiGate inspects and enforces protocols on traffic, including peer-to-peer applications on known ports. If not properly enabled, peer-to-peer traffic may bypass blocking despite the application control profile.
NEW QUESTION # 72
Refer to the exhibits. An administrator wants to add HQ-ISFW-2 in the Security Fabric. HQ-ISFW-
2 is in the same subnet as HQ-ISFW. After configuring the Security Fabric settings on HQ-ISFW-
2, the status stays Pending.
What can be the two possible reasons? (Choose two.)
- A. HQ-ISFW-2 must be authorized on HQ-ISFW.
- B. Upstream FortiGate IP must be set to 10.0.11.254.
- C. Management IP must be set to 10.0.13.254.
- D. SAML Single Sign-On must be set to Manual.
Answer: A,B
Explanation:
The Upstream FortiGate IP should match the IP address of the Fabric Root interface, which is
10.0.11.254, not 10.0.13.254.
The new device (HQ-ISFW-2) must be authorized on the Fabric Root (HQ-ISFW) before it can join the Security Fabric, otherwise the status remains pending.
NEW QUESTION # 73
Refer to the exhibit. What can you conclude from the log shown in the exhibit?
- A. The IPS socket buffer is full and IPS engine needs more memory to create new sessions.
- B. The IPS socket buffer is full and IPS engine cannot decode a packet.
- C. The IPS scan is paused by the IPS diagnostic command with bypass mode option 5.
- D. The IPS session scan is paused and reevaluating the packet because of a dirty flag.
Answer: A
Explanation:
The log message IPS session scan paused, enter fail open mode indicates that the IPS socket buffer is full, meaning the IPS engine does not have enough memory to process new sessions.
As a result, FortiGate switches to fail-open mode, allowing traffic to pass (or temporarily dropping it) without full IPS scanning.
NEW QUESTION # 74
......
RealExamFree just published the Fortinet NSE4_FGT_AD-7.6 exam dumps!: https://www.realexamfree.com/NSE4_FGT_AD-7.6-real-exam-dumps.html
Pass Your NSE4_FGT_AD-7.6 Exam Easily - Real NSE4_FGT_AD-7.6 Practice Dump Updated: https://drive.google.com/open?id=1pUpaN4VWZMMIuyBfxmMjjy703pOmCIDr
