2026 Latest NSE6_FSW-7.2 Exam Dumps Recently Updated 57 Questions
Fortinet NSE6_FSW-7.2 Real 2026 Braindumps Mock Exam Dumps
NEW QUESTION # 18
Refer to the exhibit.
The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports. and these ports are connected to endpoints which are powered by PoE. Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?
- A. Assign a new LL0P profile to handle different LLDP-ME0 TLVs
- B. Add power management as part of LLDP-MED TLVs to advertise.
- C. Define an LLDP-ME0 location 10 to use standard protocols for power.
- D. Create new a LLOP-MEO application type to define the PoE parameters.
Answer: B
NEW QUESTION # 19
What is the role of a device that is simultaneously functioning as both the distribution and core in the hierarchy network model?
- A. HA backup FortiGate managing FortiSwitch
- B. POE with high density FortiSwitch
- C. FortiGate managing FortiSwitch
- D. FortiSwitch functioning as standalone
Answer: C
Explanation:
In a hierarchical network model, the role of a device functioning simultaneously as both the distribution and core is most accurately described as "FortiGate managing FortiSwitch (B)." In this setup, FortiGate acts as the central unit managing multiple FortiSwitch units, thereby functioning both as a distribution layer-handling traffic between network segments-and as a core layer-managing traffic within the network on a broader scale. This setup is typical in medium-sized networks where a single device is capable enough to handle both roles effectively.
NEW QUESTION # 20
Exhibit.
Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)
- A. These two routes have a higher administrative distance value available to the destina-tion networks.
- B. These two routes will become primary, if the best routes are removed.
- C. These two routes will be used as load-balancing routes.
- D. These two routes are available in the hardware routing table.
Answer: A,B
NEW QUESTION # 21
Which packet capture method allows FortiSwitch to capture traffic on trunks and management interfaces?
- A. SPAN
- B. sFlow
- C. Sniffer profile
- D. TCP dump
Answer: B
NEW QUESTION # 22
What are two reasons why time synchronization between FortiGate and its managed FortiSwitch is critical in switch management? (Choose two.)
- A. FortiSwitch will not be able to become an NTP server for downstream devices.
- B. FortiSwitch cannot complete the DTLS handshake used in the CAPWAP tunnel.
- C. FortiSwitch does not retain its time after a reboot, which gets reset after each reboot.
- D. FortiSwitch will not allow other FortiSwitch devices in the chain be discovered by FortiGate.
Answer: B,C
Explanation:
Time synchronization between FortiGate and its managed FortiSwitch devices is essential for several reasons:
A . FortiSwitch does not retain its time after a reboot, which gets reset after each reboot. This characteristic of FortiSwitch underlines the importance of time synchronization with FortiGate. Since FortiSwitch loses its time settings upon reboot, synchronizing with FortiGate ensures that its system clock is accurate, which is vital for logging, troubleshooting, and security timestamping.
C . FortiSwitch cannot complete the DTLS handshake used in the CAPWAP tunnel. Accurate time synchronization is crucial for security protocols such as DTLS, which rely on timestamped certificates for establishing a secure connection. If the time on FortiSwitch is not synchronized with FortiGate, the DTLS handshake used in the CAPWAP tunnel for secure communication may fail due to time discrepancies, impacting the management and operation of the switch.
NEW QUESTION # 23
Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?
- A. Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.
- B. lt is a scalable and secure solution in comparison to other Layer 2 security measures.
- C. FortiSwitch uses only the Ethernet type to assign traffic to VLANs.
- D. It provides benefits that can be obtained when using 802.1X authentication.
Answer: D
NEW QUESTION # 24
Which statement about the IGMP snooping querier when enabled on a VLAN is true?
- A. The setting can only be enabled using the FortiSwitch CLI.
- B. Active multicast receiver entries are aging on each IGMP query sent on the VLAN
- C. IGMP reports on the VLAN are forwarded to all switch ports.
- D. All other indirectly connected switches will be unable to get IGMP multicast traffic.
Answer: D
NEW QUESTION # 25
Exhibit.
What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)
- A. The port full speed prior the split was 100G SFP+
- B. The split port can be assigned to native VLAN
- C. The FortiSwitch model is equipped with a maximum of 54 interfaces.
- D. The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.
Answer: C,D
NEW QUESTION # 26
Exhibit.
LAG and MCLAG are used to increase the available network bandwidth and enable redundancy. How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)
- A. Switch 3 and Switch 4 uplinks are treated as single interfaces.
- B. Switch 3 and switch 4 are seen as one MCLAG switch client
- C. Switch 1. Switch 2, and Switch 3 are seen as one MCLAG peer group
- D. Switch 1 and Switch 2 both seen as one single switch.
Answer: B,D
NEW QUESTION # 27
Which two statements about the FortiLink authorization process are true? (Choose two.)
- A. FortiLink authorization sets the FortiSwitch management mode to FortiLink.
- B. FortiSwitch requires a reboot to complete the authorization process.
- C. A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.
- D. The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.
Answer: A,C
NEW QUESTION # 28
Which is a requirement to enable SNMP v2c on a managed FortiSwitch?
- A. Configure SNMP agent and communities.
- B. Specify an SNMP host to send traps to.
- C. Create an SNMP user to use for authentication and encryption.
- D. Enable an SNMP v3 to handle traps messages with SNMP hosts.
Answer: A
NEW QUESTION # 29
How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?
- A. FortiGate configures and enables flow sampling on FortiSwitch but does not change existing sampling settings of interfaces.
- B. FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces.
- C. FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces, except ICL and ISL interfaces.
- D. FortiGate configures and enables egress sampling on all management interfaces.
Answer: C
Explanation:
When FortiGate exports configuration settings to a managed FortiSwitch stack with sampling mode set to "perimeter is true," the behavior is:
B . FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces, except ICL and ISL interfaces. This setting ensures that all incoming traffic on normal operational ports is sampled for monitoring and analysis purposes, but it excludes the inter-chassis link (ICL) and inter-switch link (ISL) interfaces from sampling. These exclusions are typically made to prevent the duplication of sampled data and to reduce unnecessary load on the monitoring system, as these links often carry traffic already monitored at other points.
Options A and D are incorrect because they either generalize the sampling across all interfaces without exceptions or incorrectly specify egress sampling on management interfaces. Option C is also incorrect as FortiGate can modify existing sampling settings to fit the perimeter-based configuration requirement.
NEW QUESTION # 30
Which two statements about 802.1X authentication on FortiSwitch ports are true? (Choose two.)
- A. All hosts behind an authenticated port are allowed access after a successful authentica-tion.
- B. All devices connecting to FortiSwitch must support 802.1X authentication.
- C. A local user database must be used to authenticate devices using the 802.1X authentica-tion protocol.
- D. A security policy is used to apply 802.1 authentication on a port.
Answer: A,B
Explanation:
All hosts behind an authenticated port are allowed access after a successful authentication (A): Once a device on a port successfully authenticates using 802.1X, all other devices connected behind that port also gain network access. This is typical in scenarios where a switch is behind an authenticated port and not each device individually authenticates.
All devices connecting to FortiSwitch must support 802.1X authentication (D): For a network secured with 802.1X, all devices attempting to connect through the FortiSwitch must support and participate in 802.1X authentication to gain access. This ensures that all devices on the network are authenticated before they are allowed to communicate on the network.
NEW QUESTION # 31
In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)
- A. Assign a port to a VDOM directly on the managed FortiSwitch.
- B. Switch the FortiLink interface to the target VDOM.
- C. Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.
- D. Create a virtual port pool on the FortiGate CLI.
Answer: A,D
NEW QUESTION # 32
Refer to the diagnostic output:
Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?
- A. It is a MAC address of a switch that accepts multiple VLANs.
- B. It is a MAC address of an upstream FortiSwitch.
- C. It is a MAC address of FortiLink interface on FortiGate.
- D. It is a MAC address of FortiGate in HA configuration.
Answer: A
NEW QUESTION # 33
What can an administrator do to maintain a FortiGate-compatible FortiSwitch configuration when changing the management mode from standalone to FortiLinK?
- A. Use a migration tool based on Python script to convert the configuration.
- B. Enable the FortiLink setting on FortiSwitch before the authorization process.
- C. FortiGate automatically saves the existing FortiSwitch configuration during the FortiLink management process.
- D. Register FortiSwitch to FortiSwitch Cloud to save a copy before managing with FortiGate.
Answer: D
NEW QUESTION # 34
Exhibit.
The exhibit shows the current status of the ports on the managed FortiSwitch.
Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?
- A. A standalone switch with the showm serial number is connected on por123.
- B. Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN
- C. Port23 is a member of a trunk that uses the Access-1 FortiSwitch senal number as the name of the trunk.
- D. Port23 is configured as the dedicated management interface.
Answer: A
Explanation:
The appearance of a serial number in the Native VLAN column for port23 suggests that the switch connected to this port is identified uniquely in the network. Given the options provided:
A standalone switch with the shown serial number is connected on port23 (Option C): This is the most plausible explanation. The FortiSwitch configuration interface is displaying the serial number of a standalone switch that is directly connected to port23. This kind of display helps in identifying and managing individual devices in a network setup, especially in environments with multiple switches.
NEW QUESTION # 35
Which statement about the configuration of VLANs on a managed FortiSwitch port is true?
- A. Untagged VLANs must be part of the allowed VLANs: ingress and egress.
- B. FortiSwitch VLAN interfaces are created only when FortiSwitch is managed by Forti-Gate.
- C. The native VLAN is implicitly part of the allowed VLAN on the port.
- D. Allowed VLANS expand the collision domain to the port.
Answer: C
Explanation:
The native VLAN is implicitly part of the allowed VLAN on the port (C): On a managed FortiSwitch port, the native VLAN, which is the VLAN assigned to untagged traffic, is implicitly included in the list of allowed VLANs. This means it does not need to be explicitly specified when configuring VLAN settings on the port. This configuration simplifies VLAN management and ensures that untagged traffic is handled correctly without additional configuration steps.
NEW QUESTION # 36
How are the 'by VLAN redirect MAC address quarantine' mode and the 'by redirect MAC address quarantine' mode on FortiGate similar?
- A. Both modes add quarantined device MAC addresses to the blocked firewall address group.
- B. Both modes move quarantined devices to the quarantine VLAN.
- C. Both modes require firewall policies to block inter-VLAN traffic.
- D. Both modes block intra-VLAN traffic by FortiGate automatically.
Answer: B
Explanation:
The 'by VLAN redirect MAC address quarantine' mode and the 'by redirect MAC address quarantine' mode on FortiGate share specific similarities:
Quarantine VLAN Assignment (A):
Common Feature: Both modes utilize a designated quarantine VLAN to isolate quarantined devices. This helps in mitigating the risk of spreading potential security threats within the network.
Operational Impact: Moving devices to a specific quarantine VLAN restricts their network access, effectively isolating them until further action or remediation is taken.
NEW QUESTION # 37
An administrator needs to deploy managed FortiSwitch devices in a remote location where multiple VLANs must be utilized to segment devices. No Layer 3 switch or router is present. The the only WAN connectivity is the router provided by the ISP connected to the public internet.
Which two items will the administrator need to use? (Choose two.)
- A. FortiSwitch devices that have the required internal hardware for this configuration.
- B. FortiSwitch and FortiGate devices configured with IPsec interfaces.
- C. FortiSwitch devices configured with NAT disabled.
- D. FortiSwitch and FortiGate devices configured with VXLAN interfaces.
- E. A FortiSwitch interface connected to the ISP router configured with fortilink-13-mode enabled.
Answer: C,D
NEW QUESTION # 38
Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)
- A. switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.
- B. Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.
- C. By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.
- D. Settings related to DHCP option 82 are only configurable through the CLI
Answer: A,D
Explanation:
Switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks (B): This feature of DHCP snooping helps prevent DHCP exhaustion attacks by ensuring that the destination MAC addresses in DHCP packets match the MAC addresses learned by the switch. This check helps prevent attackers from overwhelming the DHCP server with requests from spoofed MAC addresses.
Settings related to DHCP option 82 are only configurable through the CLI (D): DHCP Option 82 is used for "agent information," and it's typically used in network environments where additional information between DHCP clients and servers is necessary for policy and billing purposes. Configuration of these settings in FortiSwitch is only available through the Command Line Interface (CLI), not the Graphical User Interface (GUI).
NEW QUESTION # 39
......
Candidates for the Fortinet NSE6_FSW-7.2 exam should have a strong understanding of networking fundamentals, as well as experience working with Fortinet products. NSE6_FSW-7.2 exam is designed to test the candidate's knowledge of the FortiSwitch platform and their ability to configure and manage various features and functions of the device. Upon passing the exam, candidates will receive the Fortinet NSE 6 - FortiSwitch 7.2 certification, which is recognized in the industry as a mark of expertise in Fortinet products and networking.
Verified NSE6_FSW-7.2 Exam Dumps Q&As - Provide NSE6_FSW-7.2 with Correct Answers: https://www.realexamfree.com/NSE6_FSW-7.2-real-exam-dumps.html
NSE6_FSW-7.2 Exam Questions | Real NSE6_FSW-7.2 Practice Dumps: https://drive.google.com/open?id=1vRYwLQ565sVlxbHnJR2nyoeZ0YJ2Hfe3
